|
Vertrod Style Open Back Slant Cabinet Heat Sealer
|
| Our Open Back design allows for sealing of materials from
North, South, East and West. Jaw opening options are available
from 1" to 6" to accommodate a wide variety of
sealing applications. Slanted 45 degree cabinet facilitates
sealing of bagged powders or liquids where horizontal sealing
would result in spillage and contamination of the seal area.
Heater bar placement options available: heater bar on top
allows for trouble-free sealing of Tyvek pouches, double-sided
heat for sealing of thick materials up to 80MIL (.080")
or for sealing high temperature materials such as Teflon,
Tedlar, etc. |
|
Half inch thick aluminum table top for maximum durability.
Custom mounting options available to allow sealer to operate
at any angle, 0-360 degrees. Also available as a Table-Top
Model.
Therm-O-Seal ® Closed-Loop
Water Chillers available for all Water-Cooled Systems.
|
- Seal Lengths Available: 9", 14", 20",
24" & 30" (custom lengths & configurations
available upon request).
- Seal Widths Available: 1/8", 3/16", 1/4"
& 3/8" (custom widths & configurations
available upon request).
- Water-Cooled or non Water-Cooled Heater Bar.
- Heater Bar & Pressure Bar equipped with our easy-to-replace
Teflon.
- Hammertone Grey or FDA Compliant White
powder coated finish.
- All Stainless Steel Fasteners.
- Maintenance-Free Greaseless Needle Bearings.
- Trim Seal option available.
- PLC Time Control* or Temperature Control** System.
- User Programmable Heat Time & Cool Time*/Low
Temp & High Temp** set points.
- Measures Temperature in the actual process area
on Heater Bar(s)**
- Operator Burn Protection - Ensures that the
heated parts of the machine are not accessible to the
operator until the low temperature set point is reached.**
- Ensures that the melt temperature of the material
is reached on every cycle (accurate to within approx.
5 Degrees Fahrenheit).**
|
- User-adjustable Software Rheostat allows the
operator to program the rate of temperature rise.
- Runaway Heat Protection (shuts down all system
controls if the temperature exceeds the setpoint by
100 Degrees Fahrenheit).
- 24VDC Control Circuitry.
- 2-Line x 20-Character Operator Interface.
- Text Error Messaging.
- Numeric Keypad Input.
- LED Indicator Lights.
- 50mm Emergency Stop.
- Cycle Counter (up to 99999-resetable).
- Cycle Timer (displays Cycle Time in tenths
of a second).
- Operates on Main Power Output of 120VAC 50/60Hz
(220VAC available).
- Voltage Control (maintains constant output
to the heater element during low/high voltage episodes.
- Proximity Switch Sensing.
- Obstruction Detection (opens sealing jaws before
going to high pressure if obstruction is detected).
- Pressure Sensor - ensures that income line
pressure is adequate before allowing the operator to
begin the sealing process(optional add-on).
- Pneumatic Air Cylinder.
- Footswitch Activated.
|
|
* Time Control Systems only.
** Temperature Control Systems only. |
Ordering Instructions:
Your part number will consist of a Model Number (seal
length) and seal width e.g. part# 20OB-CAB-SL-3/16
indicates a 20" Seal Length and 3/16" Seal Width.
Compile your part number from the table below: |
|
9OB-CAB-SL
|
9" Seal Length |
1/8
|
1/8" Seal Width |
|
14OB-CAB-SL
|
14" Seal Length |
3/16
|
3/16" Seal Width |
|
20OB-CAB-SL
|
20" Seal Length |
1/4
|
1/4" Seal Width |
|
24OB-CAB-SL
|
24" Seal Length |
3/8
|
3/8" Seal Width |
|
30OB-CAB-SL
|
30" Seal Length |
|
|
Call or email
for additional information. |
|
|
